Subscribe for notification

Electronics-1 May 2015 3rd Sem Electrical Engineering Diploma Paper

Download Previous Year Diploma Solved Question Paper of Electronics-1 May 2015 3RD Sem Electrical Engineering Diploma Paper

Electronics-1 May 2015 3RD Sem Electrical Engineering Diploma Paper

                                  SECTION-A

Q1. Fill in the blanks.                                                      10×1.5=15

a) Inductance coil is ______________ element.
b) Ripple factor in full wave rectifier is ___________ .
c) Transistor is an _________ switch.
d) An ideal constant voltage source has _______ resistance.
e) Three terminals of JFET are _______,__________ ,_______-.
f) A FET has ___________ internal impedance.
g) Semi conductors have __________ bonds.
h) R-C coupling has minimum ________ distortion.
i) A capacitor circuit does not to allow to pass _______ component.
j) Usually , a zener diode is used as a ________.
k) The insulators are rated in ohm and ___________ .
l) The value of knee voltage for germanium diode is __________ volt.
m) The base of the transistor is very ______ doped.
n) The ideal value of stability factor is ________ .
o) The decibal gain is important because it tells with __________ .

                                  SECTION-B

Q2. Attempt any SIX questions.                                                                    6×5=30

I. What do you mean by active and passive components?
II. Compare the MOSFET & BJT.
III. What is the filter?
IV. Explain the need of biasing for transistor.
V. Draw JFET as an amplifier.
VI. Differentiate between DC and AC load lines.
VII. Semiconductors has negative cofficient resistance, Why?
VIII. While selecting a diode, the most important consideration is its PIV, why?

                                   SECTION-C

Q3. Attempt any three questions.                                                      3×10=30

I. Explain the working of RC coupled amplifier with the help of neat diagram.
II. With the help of circuit diagram, Explain the function of bridge rectifier.
III. On the basis of conductivity, classify the solids. Explain their behavior on the basis of energy band phenomenon.
IV. What is Zener diode? Draw the equivalent circuit of an ideal zener diode with characterstics.
V. Draw the block diagram of regulated power supply. And explain the function of each block in brief.

Electronics-1 May 2015 3RD Sem Electrical Engineering Solved PSBTE Diploma Paper

                                    SECTION-A

Q1. Fill in the blanks.                                                      10×1.5=15

a) Inductance coil is Passive Linear Circuit element.
b) Ripple factor in full wave rectifier is 0.48 .
c) Transistor is an Electronic switch.
d) An ideal constant voltage source has Zero resistance.
e) Three terminals of JFET are Cathode , Anode, Gate .
f) A FET has Three internal impedance.
g) Semi conductors have Covalent bonds.
h) R-C coupling has minimum Frequency distortion.
i) A capacitor circuit does not to allow to pass dc component.
j) Usually , a zener diode is used as a Voltage Stablizer or Voltage Regulator.
k) The insulators are rated in ohm and Voltage.
l) The value of knee voltage for germanium diode is 0.3 volt.
m) The base of the transistor is very Lightly doped.
n) The ideal value of stability factor is Zero .
o) The decibal gain is important because it tells with Signal Strength .

Inductance coil is Passive Linear Circuit element.
 

Ripple factor in full wave rectifier is 0.48 .

Transistor is an Electronic switch.
d) An ideal constant voltage source has Zero resistance.
e) Three terminals of JFET are Cathode , Anode, Gate .
f) A FET has Three internal impedance.
g) Semi conductors have Covalent bonds.
h) R-C coupling has minimum Frequency distortion.
i) A capacitor circuit does not to allow to pass dc component.
j) Usually , a zener diode is used as a Voltage Stablizer or Voltage Regulator.
k) The insulators are rated in ohm and Voltage.
l) The value of knee voltage for germanium diode is 0.3 volt.
m) The base of the transistor is very Lightly doped.
n) The ideal value of stability factor is Zero .
o) The decibal gain is important because it tells with Signal Strength .

The base of the transistor is very ______ doped.

Electronics-1 May 2015 3RD Sem Electrical Engineering Diploma Paper Click Here

Compare the MOSFET & BJT.

Need of biasing for transistor.

Related Post

Draw JFET as an amplifier.

Comparison between DC and AC load lines.

Semiconductors has negative cofficient resistance

Selecting a diode, the most important consideration is its PIV.

Electronics-1 May 2015 3RD Sem Electrical Engineering Diploma Solved Paper Click Here

Electronics-1 May 2015 3RD Sem Electrical Engineer ing Diploma Paper

MY YOUTUBE CHANNEL
JK Smart Classes Upload Lecture for Degree classes like B.TECH,M.TECH in any stream like ECE,EE,ME and Civil Engineering
JK SMART CLASSES
ER.JASWINDER KUMAR
JK SMART LECTURE
ER.JASWINDER KUMAR
Engineering Classes Upload Lecture for Polytechnic Diploma classes in any stream like ECE,EE,ME and Civil Engineering
ENGINEERING CLASSES
ER.JASWINDER KUMAR
er.jaswinder kumar
Senior Lecturer
admin: Hello Friends, I am Jaswinder Kumar Working as HOD (Senior Lecturer) at Polytechnic Engineering College. I Have Three Youtube Channel names as 1.JK Smart Classes 2.JK Smart Lecture 3.Engineering Classes for Helps the Class 12, Diploma, and B.tech Student To achieve the desired goal in an easy way.

This website uses cookies.

Read More